Wanlin Care Safety

Elderly Fall Detection Monitor · 60GHz Radar Fall Alarm

Fall Detection Monitor Without Cameras for Care Rooms in Inner Mongolia

Falls are the injury elders never plan for. The WANLIN-230 radar listens for the physics of a fall - not the sound, not the light - confirms with a spoken question, and pushes the alarm to family and caregivers. Here is the full field guide.

Wanlin Care Safety Engineering Desk · Published 20 November 2026 · Service line 16710807777 · Contact: Mr. Wang

At a glance

Care operators do not need another gadget; they need fewer blind spots. A wearable forgets to be worn. A camera raises privacy objections nobody needs. The WANLIN-230 mounts on a wall at 1.8 metres, tilts down 30 degrees, and watches its whole detection zone continuously - presence, activity, stillness, falls and prolonged stationary states - reporting each state change to the cloud within seconds.

Four sensing functions in one wall-mounted unit

FunctionWhat it does
Human presenceReal-time monitoring of whether the zone holds someone, and whether they are active or still. Presence triggers in under 300 ms - faster than PIR motion sensing - while “no one” is declared only after breathing-scale micro-motion stays absent for a full judgement window, so a sleeping resident is never counted as absent.
Fall stateRecognises the kinematics of a person falling. The state persists until the person is safely back on their feet, and the report timing is configurable (5–180 s) so brief crouches do not page anyone.
Prolonged stillnessFlags a person who stays motionless too long - fainting, sitting frozen, lying unmoving - with a configurable threshold of 1–60 minutes. The alert clears only when the person resumes activity.
Voice interactionTwo-way spoken exchange: the device asks, the resident answers, and custom wake words can be taught through a guided learning mode for hands-free help calls.

The conversation after a fall

When the radar registers a fall, the WANLIN-230 speaks first instead of paging blindly:

Caregivers see the state in the app at the same time, with the event recorded. For residents who cannot reach the device, wake words can be personalised: saying “enter learning mode” then “start learning” walks the resident through recording their own phrases (for example “someone come” or “I fell”) in a quiet room, and the device confirms each one. A voice command also restores factory settings when a room changes hands.

Coverage and mounting rules that make it accurate

ItemSpecification
Detection field100° horizontal, 80° vertical; roughly 4 × 4 m of usable coverage (shrinkable in configuration)
Mounting positionOn the wall, detection face tilted downward, centred on the resident’s main activity area
Height1.8–2.4 m; 1.8 m recommended and factory-default, with a 30° downward tilt for fall detection
Keep clearNo obstruction in front of the radar face; avoid mounting near range hoods, extractor fans, running water, air outlets, or anywhere vibration and moving objects can confuse micro-motion sensing
Fit-upMetal base plate fixed with screws into wall plugs (adhesive pad optional), device body clipped in and angled, then powered and paired

Because the radar reads micro-motion, the environment matters more than the hardware: a fluttering curtain or a robot vacuum inside the zone can delay a “no one” judgement. The manual’s advice is to survey the room before drilling - confirm network signal, keep a 220V (5V/2A adapter) socket within reach, and place the device where its beam cone covers the bed-to-bathroom path, which is where most falls happen.

What to configure first in the app

The app also keeps a 7-day history of presence and fall events with timestamps - useful for care reviews and family reassurance. Pairing runs over 4G through the companion app; a lying posture is reported about five seconds after the person lies down, and the status panel shows someone / no one, active / still, plus alarm states at a glance.

Specifications

ParameterValue
ModelWANLIN-230
Radar frequency60 GHz millimetre-wave
Wireless connection4G (companion app pairing)
Rated input5V, 2A (an under-rated adapter degrades detection performance)
Adapter input180–240V~, 50/60 Hz, 0.6A
Operating temperature-10°C to +60°C
Operating humidity0–95% RH, non-condensing
Detection coverageApprox. 4 × 4 m; 100° horizontal / 80° vertical
Indicator statesRed flashing (pairing, 90 s timeout), solid red (offline), green 3 s (connected), blue (key pressed)

Where it fits in a care safety plan

The WANLIN-230 answers the worst question in eldercare - how long someone has been on the floor? - without asking residents to wear a pendant or accept a camera. One unit per room covers the typical bedroom or lounge zone; bathrooms-adjacent placements benefit from the radar’s tolerance of steam and low light. Every state change rides the same cloud platform Wanlin uses for smoke and electrical alarms, so a single dashboard can carry fire, electrical and fall events for the whole facility, with app messages and phone calls as the escalation path. For room counts, layout review and pricing, contact 16710807777.

After-sales note: units sold in mainland China carry statutory three-guarantee service - return within 7 days and replacement within 15 days of receipt for quality issues, with repair per warranty terms. Damage from unauthorised repair, misuse, liquid ingress or expired warranty is excluded per the manual.

From this site: related products, news and FAQ

Fall detection works best as part of a room-level safety plan. The entries below are drawn live from this site’s own catalogue, newsroom and FAQ section - companion detection hardware and the context for specifying it.

Key questions, answered

Does the WANLIN-230 use a camera or a wearable?

Neither. It is a 60GHz millimetre-wave radar mounted on the wall. It senses human presence, movement, breathing-scale micro-motion and fall kinematics across a roughly 4 × 4 metre zone, and it captures no images. Detection is unaffected by temperature, humidity, noise, airflow, dust or lighting, which lets one device cover dim bedrooms and bathrooms-adjacent spaces where optical sensors struggle.

How does it avoid waking caregivers for every false alarm?

When the radar registers a fall, the device first asks aloud “Did you fall?” The resident answers “I fell” - the device confirms and notifies the guardian - or “I did not fall”, which closes the event. Configurable windows add a second filter: fall states report only after a set 5–180 second window, and prolonged-stillness alerts only after 1–60 minutes, both tuned per room in the app.

Scope disclosure: this page restates the WANLIN-230 user manual in plain English for care operators and purchasers; it is product documentation, not a certification claim, and actual radio, safety and RoHS compliance for a given shipment should be verified against the certificates for that model and market. App features depend on the companion app version and mobile network coverage. To request the full manual and a quotation, contact wanlinfirecontrol@163.com or 16710807777.

What to watch

Watch for: voice-keyword localisation beyond Mandarin, and integration between radar stay-still alerts and overnight patrol schedules in nursing facilities.

Also on this site: the full topic guide hub, express delivery station fire safety, MLPS fire IoT special report, and the site’s contact page for room surveys and quotations.

Planning radar fall detection for a care facility?

Send room counts and floor plans for a per-room mounting plan and quotation. Service line 16710807777 · Contact: Mr. Wang · wanlinfirecontrol@163.com